Electrical Circuits Objective Qustions: Part-3

Objective Questions from Circuit Theory:

[1] A balanced RYB-sequence,Y-connected(Star Connected) source with V_RN=100 volts is connected to a ?-connected (Delta connected) balanced load of (8+j6) ohms per phase.Then the phase current and line current values respectively,are[IES2010]
(a) 10A;30A
(b) 10v3A;30A
(c) 10A;10A
(d) 10v3A;10v3A
(e) None of the above

Answer: B

[2] Assuming both the voltage sources are in phase, the value of R for which maximum power is transferred from circuit A to circuit B is [GATE2012]

(a) 0.8O

(b) 1.4O

(c) 2O

(d) 2.8O

(e) None of the above

Answer:A

[3] The voltage gain A_v of the circuit shown below is [GATE2012]

(a)  |A_v| �200

(b)  |A_v|�100

(c)  |A_v|�20

(d)  |A_v|�10

(e) None of the above

Answer:D

[4] If V_A-V_B=6V,  then V_C-V_D is [GATE2012]

(a)  -5V

(b) 2V

(c) 3V

(d) 6V

(e) None of the above

Answer:A

Solution Hint:
As Va-Vb =6  => I = V/R = 6/2 = 3A
entering current = leaving current [ KCL]
so current from Vd to Vc is same  as 3A
convert the current source to voltage source
V = IR =2 x 1 = 2V

Vd = Vc + 2V + (3x1)V = Vc + 5V
Vc-Vd = -5V

[5]The circuit shown is a [GATE2012]

(a) Low pass filter with f_3db=[1/(R₁+R₂)C] rad/s

(b) High pass filter with f_3db=[1/(R₁C)] rad/s

(c) Low pass filter with f_3db=[1/(R₁C)] rad/s

(d) High pass filter with f_3db=[1/(R₁+R₂)C] rad/s

(e) None of the above

Answer:B

[6] In the circuit shown, an ideal switch S operated at 100kHz with a duty ratio or 50%. Given that?i_c 1.6A peak-to-peak and I₀ is 5A dc, the peak current in S is [GATE2012]

(a) 6.6A

(b) 5.0A

(c) 5.8A

(d) 4.2A

(e) None of the above

Answer:C 

Solution Hint:
?i_c = 1.6A peak-to-peak
The positive peak  = ?i_c /2
The current flows through the switch has a peak of =  Io +  ?i_c /2
For your information...The current waveform is like this

The lowest point will be 5A....highest point will be 5+ 0.8

[7] The i-v characteristics of the diode in the circuit given below are 

         i={ [ V- 0.7 /500]A,   V > or = 0.7 V

                                 0A,   V< 0.7 V

The current in the circuit is [GATE 2012]

(a)  10 mA

(b)  9.3 mA

(c)  6.67 mA

(d)  6.2 mA

Ans:D

(e) None of the above

Answer: D
Solution Hint:

we have to find v and then apply in ct. equ...
KVL...10 = 1K * i + v
10 = 1000i +v = 1000(v-0.7/500) + v
solve it ....v= 0.8...

[8] In the following figure, C₁ and C₂ are ideal capacitors. C₁ has been charged to 12V before the ideal switch S is closed at t=0. The current i(t) for all t is  [GATE 2012]

(a) Zero

(b) A step function

(c) An exponentially decaying function

(d) An impulse function

(e) None of the above

Answer: D
Solution Hint:
If it is RC ckt...ie any Resistance in series with capacitor, it will be an exponentially decaying function....here no resistance...so charge instantly....ie impulse function...


[9] The impedance looking into nodes 1 and 2 in the given circuit is [GATE 2012]

(a) 50 O

(b) 100 O

(c) 5 KO

(d) 10.1 KO

(e) None of the above

Answer: A

[10] In the circuit given below,the current through the inductor is [GATE 2012]

   

(a)  (2/1+j)A

(b)  (-1/1+j)A

(c)  (1/1+j)A

(d)  0A

(e) None of the above

Ans:C

Answer: A
Solution Hint: consider top half of the circuit
R & L are in parallel with ct. source....other end connected to low potential...ie GND... convert ct. to V source...